Soft Stop Soft Start Controller Forward Reverse Brake 24v Motor Speed Control 10A

Speed ControlSoft stop soft start controller forward reverse brake 24v motor speed control 10AModel: DC24RT10BLProduct Description1. PULSE WIDTH MODULATIONMotor runs quieter, with greater efficiency and less maintenance, longer life.2. FOUR QUADRANT REVERSIBLE OPERATION3. REGENERATIVE BRAKINGNo contactors required. No electromechanical components to overheat or wear out.4. ENABLE / BRAKE / DIRECTION TERMINALSChoose a function by simply opening or closing a dry contact or through an open collector transistor.5. Soft start, soft stop time adjustable6. Forward and reverse can be set separately7. Output current can be set8. Braking current can be set9. compensatio10. Standard analog control mode: Analog:0-5V or potentiometer11. Over voltage & less voltage protection12 OVER TEMPERATURE PROTECTIONDrive will fold the output power back to prevent from overheating Drive will fault if it still remains too Specification for DC24RT10BLInput voltage rangeDC24V (if you need 12V, 36V, 48V, kindly advise)Max output current10AOperating modeSpeed mode, mode, Four-quatrant mode, Regenerative BrackingControl waysPWM, 0-5V, PotentiometerProtectionAbnormalitise like over current, overheating, over voltage, less voltage and short circuit will start the protection function.Soft start/stop Soft start time: 0.2s-20s, soft stop time: 0.2s-20s, can be setted seperately.Working Temperature-10 -- +60Ambient humidityRelative humidity less than 80RHSizeL*W*H = 127*75*34 mmWeight400gProduct OverviewGeneral Connect DrawingFunction of Control Terminal1.BRAKE SWITCHRegenerative braking control: When quick stopping of motor is required, this function is suitable. Close brake switch, motor controller rapidly brakes motor's speed by the way of regenerative braking then make motor stop immediately.2.INHIBIT SWITCHEnable control: Control the start and stop of motor3.FORWARD/REVERSE SWITCHThe reversing control of motor: Rotation direction can be easily get through open or close reversing switch. Analog Quantity ControlYou can control this motor speed by analog quantity signal 0-5VInstruction and setting of adjustable potentiometer1. "ACCEL" potentiometer( Set soft start time 0.2s - 20s )Adjust "ACCEL" potentiometer to set ramp up from initial speed value to setting speed value(it means acceleration time).2. "DECEL" potentiometer( Set soft stop time 0.2s - 20s )Adjust "DECEL" potentiometer to set ramp down from Max.speed value to Min.speed value(it means deceleration time).3. "FWD MAX SP"Set the MAX forward speed.4. "REV MAX SP"Set the MAX reverse speed.5. "REGEN CL"Adjust "REGEN CL" potentiometer to limit Max. braking armature current value(it also means brake/stop time). The braking current value affect brake/stop time. 6. "IR COMP" Adjust "IR COMP" potentiometer to make motor have constant speed value in different load conditions( setting is "0").7. "MIN SP"Set the motor MIN speed8. "MOTOR CL" Adjust "MOTOR CL"potentiometer to limit motor controller's Max.output current(we also say motor's setting current value).The setting of this current should be based on motor's rated current value.Current value should be moderate.If not, is not enough or overcurrent protection is failure. Adjust this potentiometer in clockwise to increase motor controller's output current.Note: Motor controller's output current value should be twice as much as motor's rated current value in general.However,motor controller can't operate at setting value which is greater than motor's rated current value for a long time, or the motor will be burnt out.soft stop soft start controller forward reverse brake 24v motor speed control 10ARelated productsModelRated volt/VRated currentMax currentController modeRegenerationDC12/24/48RT10BL12/24/485A10APotentiometer, PWM, 0-5VYesDC12/24/48RT15BL12/24/488A15APotentiometer, PWM, 0-5VyesDC12/24/48RT30BL12/24/4815A30APotentiometer, PWM, 0-5VYesDC12/24/48RT50BL12/24/4825A50APotentiometer, PWM, 0-5VYesDC12/24/48RT100BL12/24/4850A100APotentiometer, PWM, 0-5VYesProducing==========Model Number : DC24RT10BLMotor Type : MotorVotlage : DC24VMax current : 10AContinue current : 6AControl signal : PWM, 0-5V, PotentiometerSoft start time : 0.2s-20sSoft stop time : 0.2s-20sReversible : yes

• Speed Control
• Soft Stop Soft Start Controller Forward Reverse Brake 24v Motor Speed Control 10A